Home > Setting Materials > Grout > Grout >

Laticrete Permacolor Premium Grout

Laticrete Permacolor Grout

Alternative Views:

List Price: $42.00
Our Price: $39.95
You save $2.05!

Availability: Usually Ships in 24 to 48 Hours
Product Code: 93-2525

Choose a Color

Color Chart ( click on ? )*:

Description Grout Coverage Chart
LATICRETE® PermaColor Grout
LATICRETE PermaColor Grout offers the maximum performance available in a cement-based grout, providing consistent color and Microban to resist stain-causing mold and mildew.
LATICRETE PermaColor Grout is easy to install – just mix with water.
LATICRETE PermaColor Grout is ideal for floors and walls in both interior and exterior installations.
When you must use a cement-based grout, choose LATICRETE PermaColor Grout.

LATICRETE PermaColor Grout is a high performance grout that provides a grout joint that is dense, hard and will not crack. LATICRETE PermaColor Grout is color consistent. Mix only with water.

  • Consistent Color
  • Mixes with water only
  • Ideal for floors and walls ( Joint Widths of 1/16-1/2" [1.5 to 12 mm])
  • Inhibits Mold and Mildew with Microban®
  • Component of LATICRETE 15 Year Residential Warranty (see DS 230.14)
  • Stain Resistant
  • Interior and Exterior Applications
  • Residential and Commercial

25 lb (11.3 kg) bags.

Shelf Life

Factory sealed containers of this product are guaranteed to be of first quality for one (1) year if stored off the ground in a dry area.


Applicable Standards

(ANSI A118.6 and A118.7)

Physical Properties

Tensile Strength (28 Day)
510 psi (3.5 MPa)
Compressive Strength
4500 psi (31.0 MPa)
Flexural Strength
1250 psi (8.62 MPa)
Linear Shrinkage (7 day)

Working Properties

Pot Life
40-60 min at 70°F (21°C)
Final Set
3 hrs
Heavy Foot Traffic
6 hrs

Specifications subject to change without notification. Results shown are typical but reflect test procedures used. Actual field performance will depend on installation methods and site conditions.


Surface Preparation

Before starting to grout remove spacers and debris in grout joints and remove dust and dirt using a wet sponge. Do not leave water standing in joints. Substrate temperature must be between 40°F (4°C) and 90°F (32°C). Apply grout release or sealer if necessary. Refer to LATICRETE® Grout Troubleshooting Guide for more information on grouting.


Use approximately 2 quarts (1.9 l) of clean potable water for 25 lbs (11.3 kg) of LATICRETE PermaColor Grout. No additive required. Do not use with LATICRETE 1776 Grout Enhancer or any other latex additive. Place water in a clean mixing container and add grout powder. Mix with a slow speed drill mixer (300 rpm) for 1 minute. Wait for 5 minutes and remix with drill for 1 minute.


Clean tile surface with a damp sponge. Spread with a sharp, firm rubber grout float or wall float for narrow wall joints. To remove excess grout hold the float at a 90° angle and pull it at a 45° angle diagonally across the joints to avoid pulling out the material.

Note: If the grout begins to stiffen during installation, remix with drill mixer for 10-15 seconds. DO NOT ADD MORE WATER!

Wait 15-20 minutes at 70°F (21°C). For wider joints or cooler temperatures wait longer (25-30 minutes) Begin initial cleaning by lightly wiping down entire area to be cleaned with a damp sponge. Wash with a damp sponge (not wet). Work diagonally to the joints. Allow to dry 3 hours at 70°F (21°C). For second cleaning use a damp sponge or dry cloth to remove remaining grout haze.

Additional Information

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Setting Materials > Grout > Grout
Setting Materials
Setting Materials > Grout
Setting Materials > Grout > Cement Grout
Setting Materials > Grout > Grout > Cement Grout